Heijneker

Weird staining on backboard van interior

Recommended Posts

Using OCFCP @1:3 foamed with an IK 12, I got these van's seats back from the dead. These were naaaaaastyyyyyyy.

Now the weird thing is, the overspray has stained the painted(?) metal backboard behind the seats. I haven't had this problem this bad before, but I did notice it before. I wiped the foam off right away, but noticed it had turned yellow. The backboard was cleaned with ONR already, so it probably wasn't dirt.

20220329-161627.jpg

 

20220329-161635.jpg

 

20220329-161640.jpg

 

I tried Power Clean and OCFCP again to see if I can remove it, but that didn't work.

What happened here and how do we prevent/cure it?

Share this post


Link to post
Share on other sites

Dr G's suggestion (sounds like you already tried it) - dip microfiber in concentrated Fabric & Carpet Cleaner to see if it dissolves the overspray.  I'm wondering if the protectant in OCFCP is whats streaking?

I know it's power stuff.  Before Optimum put it in stronger bottles had container leak in a cabinet and eat into the wood.

Share this post


Link to post
Share on other sites

Thanks for the quick reply, Ron!

Wow, didn't know that OCFCP was this powerful. It doesn't irritate on the skin one bit, even if let to dry. I noticed staining on glass sometimes as well, but that seemed to be the protectant. With some effort it could be removed. 

On the backboard pictured above I tried ONR concentrate to no effect. Also Hyper Polish didn't do the trick. I guess it's permanent damage. Tomorrow I may try to replicate the problem and film it.

Anyway, I'll have to think of something to minimize overspray. Maybe apply it with a soaked towel/mitt. I'll keep you updated!

Share this post


Link to post
Share on other sites

Today I tried to replicate the problem, on the same backboard even, but wasn't able to! I think I figured out the problem;

Yesterday was the first day after a 3 week hiatus. I think the OCFCP had seperated, like it does over time, but I didn't shake it before use. Today I did shake it and it didn't stain after a minute of dwell time.

It did leave a bit of residue, but an ONR damp towel took that right off.

Phew!

Share this post


Link to post
Share on other sites

Sad to report that it happened again, on another van. I wiped it off right away, but had already turned yellow and stained the backboard.

20220401-130404.jpg

Share this post


Link to post
Share on other sites

you might wanna change chemicals before you continue destroying vans across the Netherlands

Share this post


Link to post
Share on other sites

Thanks for the input. . .

I definitely don't wanna do that, OCFCP works way too good and I want to stay with OPT products. If this keeps happening I may have to, or at least think of a different way to apply. Like I said, this didn't really happen before.

I use demineralised water to dilute OCFCP, from a company that supplies to professional glass cleaners. Is that causing problems somehow? Why does the foam turn Yellow on contact?Why was I unable to replicate the problem on the previous van's backboard? Was it because I had cleaned it with ONR beforehand?

Share this post


Link to post
Share on other sites

Is there a way to remove the seats from the vehicle so you dont have to spray the entire inside of the van?

Share this post


Link to post
Share on other sites

I get overspray on plastics quite often and never seen an issue, it might have to do with the particular substrate you’re over spraying onto. 
I’d say try cutting down the dilution to like maybe 7:1 or 10:1. 
You could grab some bath towels and shove them behind the seats before spraying, may take a couple minutes but will save you from having to fix anything. 
Or maybe spray the product closer and don’t fully pressurize the sprayer?

somewhere in a thread on here Yvan said 10:1 is the better dilution  for foam

Share this post


Link to post
Share on other sites

It's a very weird problem, Stephen! I've never had an issue with plastics either. Some slight difficulties with glass but that's it. There seems to be a chemical reaction between the metal backboards and the product, turning the foam yellow and staining the backboard. I've had it happen to 3 vans now. The weird thing is, I tested on 2 vans on an invisible spot behind the seats; no reaction or staining. But then, when I sprayed the seats, the overspray that hit the backboard did react and caused staining. Very strange....

Previously I used it at 6:1, but have gotten way better results at 3:1 and using more. Stains just freaking disappear before my eyes after dwell time and using a scrub mitt. I'll try making a new solution with distilled water, hopefully that will solve my problem. Using towels behind the seats sounds like a good idea as well! Sadly not really possible on some vans, but with most it is!

Share this post


Link to post
Share on other sites

Yesterday I tested some more with OCFCP, but not on a van sadly. I foamed it with an IK Foam Pro 12 @1:3 and very liberally, it got everywhere and I let it dry for 2 hours to see if I would run into problems. It was even on the front window, side glass and rear view mirror.

I got it off everything with a regular ONR wipe, except for the dried droplets on glass. I tried reapplying straight, Power Clean 10:1 and Hyper Polish; no succes. I then grabbed the TRC Interior Scrub Mitt (AWE-SOME tool!) with just ONR 256:1 and it took it right off. Will try that on the next van as well.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now